10mm wide x 20mm height horizontally bendable RGBW LED neon flex IP65/67 - 10 metres kit ready with straight exit connectors for left and right side (Power supply not included)
RGBW LED Neon flex powered by quad LED chips (4 colours in 1 chip) 24V - RGB+4000K IP65/67
10mm wide x 20mm height LED neon flex RGBW
16 W/m – 24V DC – 72 LEDs/m – splash-proof IP65/67 – 5 wires common anode configuration
Flat design for architectural lighting. Sits flush along edges and provides a 160 degree beam angle.
This new design of RGBW LED Neon Flex integrates all 3 primary colours Red, Green and Blue with 4000K White in a single LED chip.
Power consumption is 16 Watt per meter, below you may find consumption and other data per colour:
Red LED channel: 3.92 Watt per meter, wavelength 625nm, light output 27 lm/m
Green LED channel: 4.06 Watt per meter, wavelength 525nm, light output 57.19 lm/m
Blue LED channel: 3.84 Watt per meter, wavelength 470nm, light output 8.58 lm/m
White LED channel: 4.18 Watt per meter, CCT 4000K, light output 101.89 lm/m
LED Neon flex can be cut at every 8.33cm
Please Note: You will receive a continuous run pre-installed with end-exit connectors (both ends) as shown on the image above.
If additional connectors are required, these can be purchased separately through our connectors page click HERE
It is important to test the kit before making any cuts because returns will not be accepted unless it's the full uncut 10m reel.
3 year warranty
The high quality of Hi-Line LED Neon flex products ensures low decay, which increases the LED's lifespan and assures that the level of the brightness is kept constant throughout the LED's estimated life.
Please do NOT connect more than 15 meters of LED flex in series. A LED flex of more than 15 meters in length will overloaded, due to the increased amount of current passing through, resulting in the damage of the internal FCB and failure of the product.
Please note that 30m of this product can be installed in series only with 24V power fed from both sides in parallel. Alternatively you may power RGBW LED Neon flex (24V DC) in the middle of the run (leaving 15 meters LED flex to the left and 15 meters to the right). NOTE: If cuts have been made and powering from both ends is required, our "reverse" connector will be needed for one end of the run, which can be found HERE!
All Hi-Line LED neon flex are PWM dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the product.
This LED RGBW neon flex is fully compatible with Fibaro RGBW LED Controller, Rako or ANY conventional common anode LED controller available on the market. We do also offer a wide range of RGBW LED controllers including wireless, DMX512, ZigBee, DALI and more to choose from.
The stated price is for 10m LED Flex RGBW (RGB+ Natural White) powered by 10m x 72 (4in1) quad RGBW LEDs per meter– IP65/67, 24V DC.
Selection of the LED driver (LED switch mode power supply) depending on the maximum LED Neon Flex length
To consider best power supply performance, we suggest using 20% higher capacity (Wattage) of what the rated power consumption of neon flex will be.
Note: for driving RGBW LED neon flex, you will have to combine the LED-Driver with an RGBW LED Controller.
In such a case, the LED driver is not required to be dimmable. Brightness control (dimming) and colour adjustment is still possible through the LED controller.
For further assistance, please visit our support page.
Saunas and Steam Rooms:
If you require LEDs for saunas and steam rooms, please refer to our range of IP68 LED strips, designed to withstand temperatures of up to 110 degrees.
For more information on using Neon Flex for underwater usage, please see our FAQ page.
Looking for Related Products or Accessories?
Discover compatible products and accessories by clicking the 'Related Products' tab at the top of this product description on desktop, or just after this section on mobile devices. For detailed specifications, the 'Product Specification' tab is also available at the top of this description, offering immediate access to important product details. If you need technical data or installation guides, the 'Attachments' tab is located in the same area. To refine your search within any product category, the "REFINE BY" filter system is positioned on the left side of the screen on desktops and at the top of the page on mobiles, ensuring a seamless browsing experience.
